Wiring Question

[markv10]

Hi guys one of you must know the answer to the following question or can find out for me any way lol

A very good freind of mine and myself have just imported a 2004 v10 engine & transmission wiring etc into the uk sourced from X2Builders salvage were going to be putting it in a kit car, yes you read it right a kit car and its a 7 type chassis is being constructed at the moment around the engine, pics will follow as soon as i get them, we should be picking it up in 12 days and will have a little bit of time to get it rolling before the newark kit car show.

Now the problem i have as i have been studying the wiring diagram for the engine is the signal that BCM delivers to the PCM Plug C pin 30. I need to know what the signal is. Its the deciding factor as to running the std management or going aftermarket we would prefer to run std management but if it works out that we can't then so be it.

Once i know that i can use the rest of the diagram i have to make it run and its the only thing stopping me from being sure i can make it work.

Any help would be great and thanks.

Ill get some pics asap

[markv10]

Pick the chassis up on the 26th and will be at the Newark kit car show on the 9th and 10th of June and was hoping to be able to start the engine even if only for a few seconds just to show people.

Made a start on the website take a look www.v10viento.co.uk

Soon as i get pictures of the chassis ill get them uploaded

Someone must know the information i need its all thats stopping me from getting this to run

Please help me out

[Viper]

try the US site there's lots of technical people over there

http://forums.viperclub.org/forumdisp

[markv10]

Ta for that not the site i posted the same question in before so lets hope some one can give me the answer.

I do have a good idea what it is but the last thing i want to do is trial and error and bugger up the PCM.

Last resort will be to see if anyone is close to me that dont mind me coming to do the test myself will take me 5 min to do it such an easy test to know if i can get the std ignition system to work or have to buy a standalone system any way i got 3 weeks before i want to get it started so here's hoping...................

[phil E]

I have looked in my wiring diagrams and pin 30 C1 goes from PCM to Remote Keyless entry module and links to air bag control module and then to a data link connector. In the PCM it is shown as CCD Bus +ve, pin 28 is shown as CCD Bus -ve. Is that of any help?
I can scan the page and email to you if that helps. Regards Phil

[markv10]

Sorry my mistake forgot to put 3 after C.

So what im after is the signal to plug C3 pin 30

[markv10]

Just looked at my diagram and pin30 C1 is not listed on my 2004 wiring neither is pin28

So either i have the wrong diagram or yours is better spec than mine lol

Just to check did you look at gen 3 wiring 2004 model year?

If you did then i have an incomplete list which is soo not helpful

[phil E]

Ahhhh! My wiring is for Gen 2, I cannot help with Gen 3 Sorry Mate! If I had brains I would be dangerous!

[markv10]

Thats ok mate not a problem thanks any way

[markv10]

Any one else have any more suggestions picking the chassis up next weekend and getting the engine running is the first job just to make sure we can do it and save me more expence of having to go full aftermarket management.

Thanks

[N GTS]

Mark I should be able to help you, have sent more info via email.

[markv10]

Thanks for that great info you know ill have more questions soon lol

[markv10]

Just so you can all see this is a pic taken a few days ago loads more work been done since this obviously lol still on track to collect it saturday

[Viper]

an interesting project, keep posting them pics !

[Chesta]

Will the chassis be able to handle the torque?

[markv10]

I hope so lol its had a lot of extra bars put into it to cope with the torque and i think were going to gusset most if not all the joins to make it even stronger maybe a bit of over doing it but hey who cares lol

[markv10]

Here is another one for now will have better pic's saturday after we collect it

[markv10]

Few more pics after i sat the engine in yesterday and solved the aux belt route, Any one wanna buy a almost new A/C compressor and PAS pump

[markv10]

Just as an update have had the engine fire up although it was for 2 seconds untill the anti theft system kicked in and killed the injectors.

Spoke to Dan @ DC Performance and he is sending me a new PCM that has the anti theft system deleted out of it as there is no way to bypass it according to him should be here by friday fingers crossed.

Going to be at the Newark kit car show this weekend 16th 17th so if any one is close and wants to pop in come find us will be on the luego kit car stand.

[markv10]

WOW didnt realise it had been so long since i posted this up how a year fly's by when your knee deep in doing what seams like nothing LOL.

Here is the latest picture i have its getting there now the chassis is done exhausts done all the suspension parts are done wheels are on (9x18 front 10x18 rear)



Still loads to do as you can see but ill get there