2008 Aston Martin vantage Volanti 4.3L - usual roof problem

2008 Aston Martin vantage Volanti 4.3L - usual roof problem

Author
Discussion

Tony-5xlj0

Original Poster:

10 posts

49 months

Friday 15th July 2022
quotequote all
Hi All,

I have the usual electrical problems associated possible associated with the CRM (convertible roof problem}.
Before rushing off to gat a new module fitted I would like to eliminate other possible issues.

so far I have bought a new battery but that has not solved the problem.

If I charge the car fully and immediately start the car the roof works fine along with everything else.. However after a period I start the car and the roof will not work and i get the fully illuminated dash board and it keeps telling me to stop the car before the roof will work.. This is despite me not moving an inch. Why does the roof work with a fully charged battery but not for long.

So my next thought is do I have a battery drain such as from an old tracker module.. I am going to do drain test to see if that tells me anything'

Whatever the end problem is I will have to visit a Aston Martin agent such as Banfords to either to disconnect the tracker or to flash a new CRM module ..My problem is how to I get down there with the car acting up.. I believe I can disconnect the CRM which will allow me to drive the car without all the lights and nothing working such as lights, speedo, indicators or anything else for that matter..

Any help would be appreciated.

Tony O'Brien.

DAMIT

342 posts

170 months

Friday 15th July 2022
quotequote all
All you need to know.

https://www.pistonheads.com/gassing/topic.asp?h=0&...


Just take the fuse out and everything should work as normal apart from the roof operation. So long as it is a ROADSTER

Tony-5xlj0

Original Poster:

10 posts

49 months

Sunday 17th July 2022
quotequote all
Damit,

Thank you for the reply. I have pulled fuse 69 in the foot well fuse box . I notice there is also a roof module in the boot fuse box (fuse 10.). Do I need to pull this one as well. Thanks again.

Tony-5xlj0

Original Poster:

10 posts

49 months

Monday 18th July 2022
quotequote all
Following Branford Rose video regarding draw from a defunct tracker. I have tested for parasitic draw on my NatWest when the has been at test over night and forts light are off I am getting about 1.92 milliamperes which seem higher than a car at rest . Is this normal for an Aston Martin or do I have a potential problem.

At the moment I have the fuse f69 pulled as I have a suspected convertible roof module problem at the moment. If anybody can advise or help it would be appreciated.

Tony

Tony-5xlj0

Original Poster:

10 posts

49 months

Monday 18th July 2022
quotequote all
Following Branford Rose video regarding draw from a defunct tracker. I have tested for parasitic draw on my Multi meter when the car has been rest over night and door lights are off I am getting about 1.92 milliamperes which seem higher than a car at rest . Is this normal for an Aston Martin or do I have a potential problem.

At the moment I have the fuse f69 pulled as I suspected the convertible roof module is causing the problem at the moment. If anybody can advise or help it would be appreciated.

Ps I have stated 1.92 milliamps but that my wrong unit but it 1.92 on the multi meter

Tony

Edited by Tony-5xlj0 on Monday 18th July 15:33

CPJ1970

1 posts

3 months

Wednesday 7th August
quotequote all
Hi, new to the forum (as a poster) but have read several threads around the Roof Control Module for my 08 Vantage!

Pretty sure it’s to blame for all my electrical gremlins so looking to order replacement RCM - however, where most posts state cost in the region of £500, I’m only seeing it now for £1,099+vat! Granted that the £500 is a dated price but wondered if the £1,099 is accurate? Anyone else had to replace their RCM recently?

All guidance welcomed!

Chris

Bournemouthboy

32 posts

26 months

Friday 9th August
quotequote all
What does your outside temperature read?

If the temp sensor fails (common) the roof will not open.

Outdoor temp sensor is an easy piece to swap out and inexpensive.