Tamora chassi refurb

Tamora chassi refurb

Author
Discussion

philburch

Original Poster:

209 posts

176 months

Saturday 22nd September 2018
quotequote all
Did a full body off chassi refurb on my Chimaera a few years ago as a winter project ,thinking of doing the same with my Tamora .Looking around the car there don't look much difference, can't find any information on here has any one tackled this job .Any help would be appreciated so as to not make any silly/costly mistakes.

s6boy

1,667 posts

232 months

Monday 24th September 2018
quotequote all
I am not sure about the Tamora but certainly on the Tuscan there are a few hard to find bolts which require cutting of the glass fibre.

Are you looking to do the work yourself? If so I can let you have the name of a company I used near Diss for the shot blasting and finishing.

philburch

Original Poster:

209 posts

176 months

Monday 24th September 2018
quotequote all
Hi, yes i will be doing it my self had my Chim chassi done at a company at Ella airfield nr Beccles always open to recommendations.The only bolts i'm not sure about are the ones neat the gear lever. Can't find any information on here anywhere unless i'm not looking in the right place.

s6boy

1,667 posts

232 months

Tuesday 25th September 2018
quotequote all
It sounds like the Tam is the same as the Tuscan then (no surprise really) the bolts you refer to need the trim pulling back from behind the gearstick on the console and glass fibre cut, but it took a couple of goes on mine before finding the right place.

I used a company called Blast Power just outside Diss. They do everything on site from the blasting - funnily enough smile to whatever coatings and finish you want. Had very good service from them including regular photos of progress.

philburch

Original Poster:

209 posts

176 months

Tuesday 25th September 2018
quotequote all
What is the reason the bolts are glassed over??. Will look that company up when i get the car stripped down Diss isn't that far away from me.

philburch

Original Poster:

209 posts

176 months

Sunday 4th November 2018
quotequote all
Made a start today on getting the body off,going in to this a bit blind as all my searches have drawn bit of a blank. First job get garage clean an d tidy. Found two bolts on top of the tunnel,after removing the dash . hopefully these are the only two ??????.If any one knows other wise please let me know. If people are interested will stick more photo's up as i go.

Geoff A

351 posts

213 months

Sunday 4th November 2018
quotequote all
Yes please, we need pics wink

rfisher

5,024 posts

290 months

Tuesday 6th November 2018
quotequote all
Take a look at this old thread for some useful info;

https://www.pistonheads.com/gassing/topic.asp?h=0&...

philburch

Original Poster:

209 posts

176 months

Tuesday 6th November 2018
quotequote all
Hi,thank's for that link, it will give me the urge to carry on when the going gets tough. Busy day today ,removed the petrol tank,exhaust ,radiator and all 26 body bolts+6 more holding the pedal box in .
How many bolts do you need

philburch

Original Poster:

209 posts

176 months

Sunday 11th November 2018
quotequote all
Spent another couple of hours on the car today , ended up taking the peddle box out just to get at one bolt.
Picture of the parts taken of the car so far ,
Should be ready next weekend to lift of the body ,mates willing.

philburch

Original Poster:

209 posts

176 months

Monday 12th November 2018
quotequote all
Unexpected free time this morning thought i would get the car ready for next weekend , lifted the body up 3-4 inch so as to check everything is disconnected and all is looking good. Wasn't sure about taking the exhaust manifolds off but thankfully the body will come past them. Looks like it should have 4 wheel drive.[url]

s6boy

1,667 posts

232 months

Monday 12th November 2018
quotequote all
Did you decide on a place to carry out the chassis refurb?

philburch

Original Poster:

209 posts

176 months

Monday 12th November 2018
quotequote all
Have phoned blast power several times all i get is the answering machine but will keep trying,spoke to a company near Colchester do a lot with Tvr's but the y were thinking about £1500 . Which is way more than i paid last time . From what i can see it doesn't look like it will want any welding.

philburch

Original Poster:

209 posts

176 months

Monday 12th November 2018
quotequote all
Have phoned blast power several times all i get is the answering machine but will keep trying,spoke to a company near Colchester do a lot with Tvr's but the y were thinking about £1500 . Which is way more than i paid last time . From what i can see it doesn't look like it will want any welding.

s6boy

1,667 posts

232 months

Tuesday 13th November 2018
quotequote all
Hi Phil I have just spoken to Blast Power, they've said just to leave a message as they are very busy with all hands working outside.

s6boy

1,667 posts

232 months

Tuesday 13th November 2018
quotequote all
Just read what you had been quoted...that's steep but about average with what I was quoted by other places.

plasticman

903 posts

258 months

Tuesday 13th November 2018
quotequote all
Does that include powder coating or gold plating ?

philburch

Original Poster:

209 posts

176 months

Sunday 18th November 2018
quotequote all
Couple of hours spare today got the body of and the chassi in the garage ready to start stripping it down this week.
Don't like the way the fuel lines are just left to flap around on top of cover.
Have left a message with Blast Power but as yet no reply.
Has any one fitted the poly bushes that Tvr parts sell,if so what do you think of them,or would you stick with the original bushes??

Geoff A

351 posts

213 months

Sunday 18th November 2018
quotequote all
I used poly for the diff only. Last winter, I replaced every wishbone bush, drop link and ARB on the Tam with OEM parts from Power, followed by a full Geo. The ride quality was improved enormously compared to the 13 year old originals, and felt supple and compliant, making the car more enjoyable on our crappy roads.

Just pop the new bushes in the deep freeze for an hour to two to help when pressing back in.

philburch

Original Poster:

209 posts

176 months

Tuesday 20th November 2018
quotequote all
Thank's ,that's a good tip,thinking i might try the poly bushes haven't made my mind up yet.Had a good day in the garage today,apart from the oil pipes being a complete baxxxd to get undone all went well.
Decided to take the gearbox of first before lifting the engine out,the engine just fits through the gap with only a few mill to spare.
After that made a start on stripping the suspension of,only had time to do one corner,if all go's well tomorrow might get finished.