Equivalent Part Numbers
Discussion
warpspeed said:
Just been into Evans Halshaw with Coil Pack part numbers 413545061 and N92512. Parts guru had no idea and stated that these were not Citroen part numbers. Can anyone shead any light on this and perhaps come up with the Citroen part number ? The number should be a combination of three to four letters and numbers after it.
These are "German, Swedish & French" or "Eurocarparts" numbers. Not official Citroen numbers.http://www.gsfcarparts.com/ : N92512
http://www.eurocarparts.com/ : 413545061
TT Tim found the track rod ends.
Also today I found the Radiator cotton reals are actually Rover Mini Exhaust mounts from 1990 onwards.
Halfords sell them for 99p including the nuts!
Also, the Halfords Type 072 battery DOES NOT FIT AT ALL!!!! It's too tall.
Still working on the exhaust rings, either Ford Capri or Mr KwikFit thought it could be off a Mercedes Vito.
Also today I found the Radiator cotton reals are actually Rover Mini Exhaust mounts from 1990 onwards.
Halfords sell them for 99p including the nuts!
Also, the Halfords Type 072 battery DOES NOT FIT AT ALL!!!! It's too tall.
Still working on the exhaust rings, either Ford Capri or Mr KwikFit thought it could be off a Mercedes Vito.
Edited by ridds on Monday 24th March 19:32
gave up in the end with the track rod ends.spent ages looking though everthing my local factor had, nothing matched. and i'm affraid nearly right isn't good enough for me
ordered a pair from tvr power, bout 16 quid each+, which isn't too terible.
just wanted the car back on the road that day.
be interested to know what tt tim came up with though.
ordered a pair from tvr power, bout 16 quid each+, which isn't too terible.
just wanted the car back on the road that day.
be interested to know what tt tim came up with though.
A couple of alternative part numbers for the handbrake shoes and the fuel filter
The handbrake shoes I got were APEC Braking part number SHU-482
The fittings kit the go with it (springs, etc) is APEC part number 766.
An alternative fittings kit is the Quinten Hazell one BFK-351.
The fuel filter I used is a Bosch one and the number on it is 957.
Also, when fitting the fuel filter the bolt holding it in place will most likely be rusted and have to be cut out so it's a good idea to have an M8 x 50mm stainless steel bolt, 2 x M8 stainless steel washers and an M8 Nyloc nut on hand.
The handbrake shoes I got were APEC Braking part number SHU-482
The fittings kit the go with it (springs, etc) is APEC part number 766.
An alternative fittings kit is the Quinten Hazell one BFK-351.
The fuel filter I used is a Bosch one and the number on it is 957.
Also, when fitting the fuel filter the bolt holding it in place will most likely be rusted and have to be cut out so it's a good idea to have an M8 x 50mm stainless steel bolt, 2 x M8 stainless steel washers and an M8 Nyloc nut on hand.
warpig said:
gave up in the end with the track rod ends.spent ages looking though everthing my local factor had, nothing matched.
They're Rover SD1 items.They are slightly shorter than the one taken off my car, but there's plenty of thread on the track rod itself so I think it's okay. Several people, including myself have now fitted these and they are perfect.
The ends are from a Rover SD1.
OE part no.: GSJ149
Quinton Hazell no.: QR1573S
FirstLine: FTR4073
Delphi AP: TA723
Motaquip: VTR123
Powertrain: PSTR19
Sidem: 65230
Swag: 182-300
Veco: VB366
(cross ref' taken from QH sources)
Hope this is helpful.
Tim
LEGAL BIT: I make no guarantees about this, if you choose to try this you do so at your own risk.
Edited by TT Tim on Sunday 30th March 10:41
Edited by TT Tim on Sunday 30th March 10:42
Rear diff output seals are 38mm bore 52mm OD and 10mm Thick, double lipped.
They can be brought from here:- http://simplybearings.co.uk/shop/p26905/38x52x10mm...
Only £5.40 ea!
They can be brought from here:- http://simplybearings.co.uk/shop/p26905/38x52x10mm...
Only £5.40 ea!
Thought Power steering pumps were already here but seems not
Landrover 300TDi amongst others, Part Number ANR2157 I believe.
Island 4x4 (e-bay) sell for £56.99 plus £7 delivery (new apparently). Loads in stock.
If I get one and fit it I will confirm all OK. As mine is speed six it is straight forward and woodruff key not such an issue. Will replace Feed and return hoses, but will get them from a local hose supplier. I know return is 5/8" I/D, not delved far enough to confirm feed. Couple of meters of each more than enough with plenty spare.
Landrover 300TDi amongst others, Part Number ANR2157 I believe.
Island 4x4 (e-bay) sell for £56.99 plus £7 delivery (new apparently). Loads in stock.
If I get one and fit it I will confirm all OK. As mine is speed six it is straight forward and woodruff key not such an issue. Will replace Feed and return hoses, but will get them from a local hose supplier. I know return is 5/8" I/D, not delved far enough to confirm feed. Couple of meters of each more than enough with plenty spare.
Standard Motor Products Europe LTD, affiliated with Intermotor list part numbers and vehicles fitted to for..
Air Temperature Sensor
Ignition Coil
Oxygen Sensor Titania 3 wires Precat
Throttle Position Sensor (blue and white)
I was looking for Throttle pots and came up with this site. The list of cars is extensive including nearly all modern Rovers.
Blue pots are listed against Speed Six and 4.5, whites against '4.3'
Sorry I am not supplying all details on site, but worth a look
www.partfinder.smpeurope.com
Air Temperature Sensor
Ignition Coil
Oxygen Sensor Titania 3 wires Precat
Throttle Position Sensor (blue and white)
I was looking for Throttle pots and came up with this site. The list of cars is extensive including nearly all modern Rovers.
Blue pots are listed against Speed Six and 4.5, whites against '4.3'
Sorry I am not supplying all details on site, but worth a look
www.partfinder.smpeurope.com
Buffoon said:
Further to Handbrake shoes, ordered mine through David Manners (jag), as I use them a lot. £38.92 incl VAT and Delivery. Not an enormous saving but every penny counts. Could not find a Peugeot 605 outlet any cheaper
When they arrive and proven I will update this with part number. Should be OK as I ordered against an XJS 91-96 as per APEC website link on main parts page.
Anyone had any luck with rear discs yet? Racing Greens vented seem best at moment, but £130 each
Well although the shoes were reported to be the same as the Peugeot, they did not fit in the end. Too wide. Sorry if anyone has experienced the same. Will delete original postWhen they arrive and proven I will update this with part number. Should be OK as I ordered against an XJS 91-96 as per APEC website link on main parts page.
Anyone had any luck with rear discs yet? Racing Greens vented seem best at moment, but £130 each
Buffoon said:
Buffoon said:
Further to Handbrake shoes, ordered mine through David Manners (jag), as I use them a lot. £38.92 incl VAT and Delivery. Not an enormous saving but every penny counts. Could not find a Peugeot 605 outlet any cheaper
When they arrive and proven I will update this with part number. Should be OK as I ordered against an XJS 91-96 as per APEC website link on main parts page.
Anyone had any luck with rear discs yet? Racing Greens vented seem best at moment, but £130 each
Well although the shoes were reported to be the same as the Peugeot, they did not fit in the end. Too wide. Sorry if anyone has experienced the same. Will delete original postWhen they arrive and proven I will update this with part number. Should be OK as I ordered against an XJS 91-96 as per APEC website link on main parts page.
Anyone had any luck with rear discs yet? Racing Greens vented seem best at moment, but £130 each
Not seen this mentioned on this thread before.
Front and rear wheel bearing/hubs (they come as one unit and bearings are non changeable) are from Jeep Grand Cherokee/Wrangler. They are the front hubs from the jeep and fit all corners of the Cerb, Tuscan, Sag, 350.
Google or Ebay 513084 and you will find them around £50 inc shipping from the states. Uk prices are around £140!
Front and rear wheel bearing/hubs (they come as one unit and bearings are non changeable) are from Jeep Grand Cherokee/Wrangler. They are the front hubs from the jeep and fit all corners of the Cerb, Tuscan, Sag, 350.
Google or Ebay 513084 and you will find them around £50 inc shipping from the states. Uk prices are around £140!
Gassing Station | Cerbera | Top of Page | What's New | My Stuff