Carbon Fibre bits

[400SE Dave]

Just put these on the Exige. Full Carbon Fibre, not the blended with Glass stuff, so now it is so light is goes 6 squillion mph





There are other bits available to but right now I didn't go for them.... but in time....





Always wanted to keep the car standard but I couldn't resist

[mikeulster500]

Dave,

They look the business! Where did you get them from?

Mike

[400SE Dave]

mikeulster500 said:

Dave,

They look the business! Where did you get them from?

Mike

Thanks Mike.

They were a direct fit as well, took only a few minutes, as they were moulded from parts taken off an S2 so all the holes needed for fixing are in the right places. They are really good quality and obviously extremely light. He tells me the centre tunnel for example is only 35% the weight of the original ally one.

Anyway,I got them though a great chap I met through the TVR Club strangely!! I'll send you a PM with his details, no point me getting in the middle.

Cheers, David

[Fatrat]

David

I'd be gratefull if you could also PM me with his details.

Don't know if he can help. I've got an S1 and like you really want to keep the car as standard as possible but they look great....

[nsm3]

How much for the sidestep covers?

They look great - my OE ones are scratched to buggery.

Do they go over the originals or do you have to remove them?

[400SE Dave]

Fatrat said:

David

I'd be gratefull if you could also PM me with his details.

Don't know if he can help. I've got an S1 and like you really want to keep the car as standard as possible but they look great....

Will send a PM with the details now.

Cheers, David

[400SE Dave]

nsm3 said:

How much for the sidestep covers?

They look great - my OE ones are scratched to buggery.

Do they go over the originals or do you have to remove them?

I'll send a PM with some info and also the contact details as better you deal with him direct.

These are replacements but all the holes are in the right places so it is an easy fit, took me about 10 mins per side, the longest part of the job was getting the originals off!!

HTH.

Cheers, David

[Stan.]

That's looking good Dave, you know it wont end there dont you?

I started off with the sill covers.

Then fitted speaker panels,

then centre console,

then door panels..

[400SE Dave]

Stan. said:

That's looking good Dave, you know it wont end there dont you?

I started off with the sill covers.

Then fitted speaker panels,

then centre console,

then door panels..

I know, I know, it is a slippery slope. Like the speaker covers and the centre console, looks really good. I did say last week that it really needs speaker covers to complete the door opening part.

Need to save a few more pennies and then talk sweetly to my good lady

[n_wootton]

i know there are aseveral having been done before (the australian one wiht the audi engine and the sebon one for example) - in fact you can still buy front and rear clams from some american for an S2 - but has anyone discovered anyone who can provide a full set of carbon body panels for either S1 or S2 'off the peg' - or are sebon the only ones?

[mrluke]

I never did thank you Dave for Jons details . So thank you

Heres most of mine fitted

Things still to do .

Stearing column plastic in carbon .

Replace Mats with Black Elise mats

Leather the Vent trim panel ( after my replacement comes as i broke this one )


[img=150x112]http://img262.imageshack.us/img262/3619/img0165fn.th.jpg[/img]
[img=150x112]http://img831.imageshack.us/img831/2594/img0166o.th.jpg[/img]
[img=150x112]http://img27.imageshack.us/img27/5898/img0167i.th.jpg[/img]
[img=150x112]http://img29.imageshack.us/img29/5185/img0168hy.th.jpg[/img]
[img=150x112]http://img291.imageshack.us/img291/4613/img0169qy.th.jpg[/img]
[img=150x112]http://img402.imageshack.us/img402/6655/img0170m.th.jpg[/img]
[img=150x112]http://img510.imageshack.us/img510/3829/img0172o.th.jpg[/img]

Edited by mrluke on Thursday 3rd February 22:38

[GTRene]

nice stuff, though I would always keep some or most parts in alcantara I think.

[wukfitz]

400SE Dave said:

Thanks Mike.

They were a direct fit as well, took only a few minutes, as they were moulded from parts taken off an S2 so all the holes needed for fixing are in the right places. They are really good quality and obviously extremely light. He tells me the centre tunnel for example is only 35% the weight of the original ally one.

Anyway,I got them though a great chap I met through the TVR Club strangely!! I'll send you a PM with his details, no point me getting in the middle.

Cheers, David

Hi David,

Would you be so kind as to PM me some details too, they look great.

Chris

[400SE Dave]

wukfitz said:

Hi David,

Would you be so kind as to PM me some details too, they look great.

Chris

PM sent

[400SE Dave]

mrluke said:

I never did thank you Dave for Jons details . So thank you

Heres most of mine fitted

Things still to do .

Stearing column plastic in carbon .

Replace Mats with Black Elise mats

Leather the Vent trim panel ( after my replacement comes as i broke this one )

No worries glad it all worked out.

The pictures look great. Where did you get the speaker covers from??

[mrluke]

400SE Dave said:

No worries glad it all worked out.

The pictures look great. Where did you get the speaker covers from??

Thanks

I got all my other bits from http://www.lmcorse.com/

Ive tried to contact Jon to see if we can do a group buy on a steering column and C panel ( where the vents are ) but have not heard from him yet

Regards
Luke