Tempted by new wheels for the Z06!
Discussion
I am a big fan of black split rims with polished rims, especially the Fikse FM5 as I had on my old Camaro, but you can't buy them in Z06 sizes yet. Best wheel for the Z06 I have seen so far is the GT2 made by LG Motorsports, aping the design of the GMAC Race Cars.
http://www.lgmotorsports.com/catalog/product_info....
http://www.lgmotorsports.com/catalog/product_info....
I imported these via a UK distributor/dealer
http://iforged.com/showroom/main.php?g2_itemId=110...
17" & 18" two piece/three piece racing wheels.
Fine - except the valve stems were in the centre of the rim, not on the outside and there wasn't enough room for the brake calipers. The offests were wrong so the tyres sit proud of the wheel arches.
Judging from all the photo shots of Corvettes with fancy wheels you'd think they knew what they were doing. I clearly didn't.
Guess about the tyre pressure sensors.........
http://iforged.com/showroom/main.php?g2_itemId=110...
17" & 18" two piece/three piece racing wheels.
Fine - except the valve stems were in the centre of the rim, not on the outside and there wasn't enough room for the brake calipers. The offests were wrong so the tyres sit proud of the wheel arches.
Judging from all the photo shots of Corvettes with fancy wheels you'd think they knew what they were doing. I clearly didn't.
Guess about the tyre pressure sensors.........
5 USA said:
Car's looking good VHR 'though I'm not sure about your photo location.
Is that HM Prison, Bellmarsh?
Similar.....outside wheel / tyre fitters in Tewkesbury.Is that HM Prison, Bellmarsh?
Black rims are so much easier to look after than anything shiny when your car is a daily driver in the UK. If the car was in a sunny US state or a summer show queen then I would happily swap back to the factory chromes or so aftermarket bling rims.
I would have thought black rims looks just as crap dirty as shiny ones would. Having fitted carbon brakes to mine I at least don't get all the crud dust sprayed over the rims as I did when I was using the standard pads. Much better feel too. Luckily I don't have to use my Vette as a daily drive. Wouldn't feel special.
JenkinsComp said:
I am a big fan of black split rims with polished rims, especially the Fikse FM5 as I had on my old Camaro, but you can't buy them in Z06 sizes yet. Best wheel for the Z06 I have seen so far is the GT2 made by LG Motorsports, aping the design of the GMAC Race Cars.
http://www.lgmotorsports.com/catalog/product_info....
Similar cross over spoke pattern to the new ZR1 wheels. This machined version is my favourite.http://www.lgmotorsports.com/catalog/product_info....
Hi Guys,
I wouldn't say my 360 Forged's are falling to pieces. But Martin is right, the chrome finish on the outer "lips" as Americans call them ("rims" in British English) are suffering "scabbing".
This is unacceptable on wheels of this cost and 360 Forged have advised they will supply new "lips".
However, there is a thread running on www.corvetteforum.com which suggests this will, or alternatively will not, happen. Right now, I am remaining optimistic - and I will report what happens.
Best Regards to all,
Chas
I wouldn't say my 360 Forged's are falling to pieces. But Martin is right, the chrome finish on the outer "lips" as Americans call them ("rims" in British English) are suffering "scabbing".
This is unacceptable on wheels of this cost and 360 Forged have advised they will supply new "lips".
However, there is a thread running on www.corvetteforum.com which suggests this will, or alternatively will not, happen. Right now, I am remaining optimistic - and I will report what happens.
Best Regards to all,
Chas
jagman said:
However, there is a thread running on www.corvetteforum.com which suggests this will, or alternatively will not, happen. Right now, I am remaining optimistic - and I will report what happens.
Ah, they're under new ownership aren't they?Am surprised that these lips aren't stainless but they do love their chrome over there.
Gassing Station | Corvettes | Top of Page | What's New | My Stuff