Grand Sport C4 help required.
Discussion
Trying to locate a pair of Corvette Grand Sport wheel mouldings / fender flares.
Tried all over the net and had no luck with Ecklers, Mid-America, Zip etc etc
Tried Eurovettes and Claremont in the UK already.
Anybody have a set or know where i can get a pair ?
Thanks if you can help.
Tried all over the net and had no luck with Ecklers, Mid-America, Zip etc etc
Tried Eurovettes and Claremont in the UK already.
Anybody have a set or know where i can get a pair ?
Thanks if you can help.
[url]www.corvettetraderonline.com/store/product.php?productid=168[/url]
And the GS registry do the Euro extensions !!
[url]www.grandsportregistry.com/store.htm[/url]
And the GS registry do the Euro extensions !!
[url]www.grandsportregistry.com/store.htm[/url]
I bought a combined 24 inches of rear wheel/tyre width for my C4.
Ebay natch, seemed like a good idea after a few beers, and now i have the famous carlos fandango superwide wheels look. Tasteless and expensive !
The arch lips should
a. get plod off my back by rendering my vehicle legal again.
b. Make it look less redneck.
Now if I could only find Jean Pierre Luniere super skis..............
Ebay natch, seemed like a good idea after a few beers, and now i have the famous carlos fandango superwide wheels look. Tasteless and expensive !
The arch lips should
a. get plod off my back by rendering my vehicle legal again.
b. Make it look less redneck.
Now if I could only find Jean Pierre Luniere super skis..............
Edited by tpivette on Tuesday 5th December 13:02
The fronts are a fine size, dead flush with the edges....
[URL=www.putfile.com/pic.php?img=4180701][/URL]
[URL=www.putfile.com/pic.php?img=4180700][/URL]
but the rears (and excuse the boxes and other wheels lying around) are a bit redneck
[URL=www.putfile.com/pic.php?img=4180702][/URL]
[URL=www.putfile.com/pic.php?img=4180704][/URL]
hence the arch extensions. Somebody told me i could have the back faces of the wheels milled down a bit but that seemed a bit dodgy to me.
[URL=www.putfile.com/pic.php?img=4180701][/URL]
[URL=www.putfile.com/pic.php?img=4180700][/URL]
but the rears (and excuse the boxes and other wheels lying around) are a bit redneck
[URL=www.putfile.com/pic.php?img=4180702][/URL]
[URL=www.putfile.com/pic.php?img=4180704][/URL]
hence the arch extensions. Somebody told me i could have the back faces of the wheels milled down a bit but that seemed a bit dodgy to me.
Edited by tpivette on Tuesday 5th December 22:20
i will get some pics when i can get it out next, might be a week or so yet.
the bmw pcd is 120mm the chevy at 4.75inch = 120.65mm. They bolted straight on, no worries. 0.62mm is less than a bawhair. I just had to watch out for the offset.
The hub size for bmw is i think 74mm, whereas chevy is 72.5.
the bmw pcd is 120mm the chevy at 4.75inch = 120.65mm. They bolted straight on, no worries. 0.62mm is less than a bawhair. I just had to watch out for the offset.
The hub size for bmw is i think 74mm, whereas chevy is 72.5.
Here are some shots of my Corvette with the wheels on.
The rears are "just" illegal, if such a thing exists.
Do I need Grand sport flares ?
[URL=www.putfile.com/pic.php?img=4376075][/URL]
[URL=www.putfile.com/pic.php?img=4376076][/URL]
[URL=www.putfile.com/pic.php?img=4376074][/URL]
[URL=www.putfile.com/pic.php?img=4376073][/URL]
[URL=www.putfile.com/pic.php?img=4376072][/URL]
[URL=www.putfile.com/pic.php?img=4376071][/URL]
obviously still need to get centre caps.....
The rears are "just" illegal, if such a thing exists.
Do I need Grand sport flares ?
[URL=www.putfile.com/pic.php?img=4376075][/URL]
[URL=www.putfile.com/pic.php?img=4376076][/URL]
[URL=www.putfile.com/pic.php?img=4376074][/URL]
[URL=www.putfile.com/pic.php?img=4376073][/URL]
[URL=www.putfile.com/pic.php?img=4376072][/URL]
[URL=www.putfile.com/pic.php?img=4376071][/URL]
obviously still need to get centre caps.....
Gassing Station | Corvettes | Top of Page | What's New | My Stuff